Machine-Type: M0521
Hot cutting
Working width:
Type 1:
40cm - 140cm
Type 2:
40cm - 200cm
Type of material to cut:
flat
hose
Consisting of the following modules:
- Base frame
- Extractor with dancer system
- Shape punching device (hot cutting)
- Transport roller system with length measuring device
- Cross cutter with wavy blade (hot cutting)
Cutting shapes:
Options:
Description:
This compact, horizontal cross-cut punching machine, model M0521, complements our M0564 cutting machines. In its compact design, the machine requires little space and is delivered fully assembled in the working width 220cm. Due to the design only a relatively small suction for the resulting cutting vapors is needed. The suction device is installed by the customer in the middle of the machine after assembly. The machine is also suitable for cutting tubing and gusseted tubing. The die punches can be changed very easily and without much time.
Detailed Options:
Mobile material cart
This trolley consists of a steel frame and four swivel castors, two of which are equipped with a brake. In addition, the car has a material receiving rod with two lateral Bergrenzungsscheiben or two cones.
Lifting devices without edge control
The device is a cost-effective alternative to our V3130 edge control hoist. In our experience, most of the fabric roll is now straight-edged. Even if small displacements occur on the fabric rolls, our machines still have a centrally extending material web. It can roles, as with the model V3130 to max. 1000 kg are lifted. The pickup bar for the material rolls is equipped with two aluminum rings, which serve for lateral fixation of the rolls. The applied brake band reduces the running of the roller during a stop.
Lifting devices with edge control
This lifting device with edge control, model V3130, can handle material rolls up to max. Lift 1000 kg. Next, the station with a receiving rod and two rings, which serve for lateral fixation of the rollers, stocked. A product edge is constantly scanned during the run over 2 photocells and automatically corrected by the integrated actuator when the goods are running. The material web therefore always enters a defined position in the subsequent machine. The applied brake band reduces the running of the roller during a stop.
Line and dot marking system with pen
V2001-02 Inexpensive marking device with pen holders and rail system for applying lines and / or dots. When marking points, the material flow stops for a short time and the pen is lowered onto the material.
4-point marking system with pen
V2002-4P Inexpensive marking device with four pen holders for marking 4 points. The pen holders can be adjusted with an adjustable cross to the respective size. If a circle or shape cutter is used, the dots are applied at the same time as the blank.
Fast marking system with spray head
This marking system applies dots and lines without stopping the material. This system can be integrated into almost all types of machines as it uses its own control electronics. The system is integrated in a compact frame which also allows installation in third-party systems.
Automatic depositing device with gripper u. Lift table
This depositing system is used when an automatic storage of the blanks is required. The material is taken over by the integrated gripper system behind the cross cutting system and extended to length. Once the length has been reached, the cross-section is made and the material is deposited on the lifting table. The lift table lowers automatically when the cut pile becomes larger.
Stacking table
The storage table consists of a tubular steel frame and table top. On request, this can be ordered with a false floor. The table depth is 100cm. The table width results from the working width of the machine.
Technical data:
| Working width: | 140cm / 220cm (special sizes on request) |
| Cuttting system: | Blade with wavy shape / shape punch (hot cutting) |
| O – Punch: | Ø 200mm – 590mm (each tool has a fix size) |
| X – Punch: | 200mm – 590mm (each tool has a fix size) |
| Power connection: | 400V / 50Hz |
| Compressed air connection: | approx. 8bar |
| Operating air pressure: | approx. 6bar |